Sealand DTM04 Tank Monitor System Manual Instrukcja Użytkownika Pobierz pdf (Strona 4)

TANK MONITOR SYSTEMS

INSTALLATION

Adjustable Tank Probe Cap

1. Thetankprobecapisdesignedfora3-inchFPTopening.Orderpartnumber230272iftankismadeofrigid

materialandisnotaSeaLandholdingtank.

2. Loosencompressionnuts on adjustable probesandinstallthecapintothetank.Slidethe#1probedown

untiltheoattouchesthebottomofthetank.Tighten#1compressionnutandmarktheprobeatthetopof

thenutwithapenorpencil.Donotcuttheprobe’stubingatthismark.Loosenthecompressionnut,slide

theprobeup,andcarefullycutthe#1probe’stubing1-5/8inch(41.3mm)belowthemarkwithoutdamaging

theswitchwires.Pullthewiresthroughtheblackwirecoverandpushtheprobedownintothecompression

nutuntiltheblackwirecovertouchesthecompressionnut.

3. Removecapfromtankandadjustthe#2probefor1/2fulllevelforgrayandblackwatertanksor1/4fulllevel

forfreshwatertanks.Tightenthecompressionnutandcuttheprobe’stubingoff3/8-inch(9.5mm)abovethe

compressionnutwithoutdamagingtheswitchwires.Sliptheblackwirecoverontothetopofthestem.

4. Tomakethe#1oatswitchactivatethe“Empty”light,theoatmustbepositionedwiththerecessedshoulder,

whiteband,ortheletters“NO”atthebottom.RemovetheC-clipfromtheswitchbody,iptheoat180degrees,

andreplacetheC-clip.(SeeDiagram#1.)

5. The#2oatswitchcanactivatethe“Mid”lightonblackandgraywatertanksandactivatethe“Low”lighton

freshwatertanks.Therecessedshoulder,whiteband,ortheletters“NO”shouldbefacingupforblackand

graywatertanksanddownforfreshwatertanks.(SeeDiagram#2.)

6. Route18-gaugestrandedcopperwirefromtheindicatorpaneltothelevelindicatorcap.Usequick-discon-

nectterminalsonoatswitchwirestopreventtwistingwireswhenremovingthecap.Withcapremovedfrom

thetank,connectthewiresaccordingtothewiringdiagramandtesttheoatsbymovingthemupanddown.

DisconnectthewiresandinstallthecapwiththeO-ringintothetank,thenreconnectthewires.

7. Forcapswithvents,route5/8-inchventhosefromthethrough-hullttingtotheventconnectiononthelevel

indicatorcap.Usestainlesssteelhoseclampstosecuretheventhoseconnection.

Monitor Panel

1. Selectamountinglocationawayfromdirectcontactwithwaterandoil.Drylocationsinthebathroom,salonor

galleyaremostdesirable.

2. Conrmclearancesforthepanelandwireconnectionsbehindwalls,hulllinerorbulkhead.

3. Cutoutmountingholes(seetemplateforpaneland

fastenerholelocations.)

4. Donotmountthecircuitpaneluntilwiringisrouted

andproperlyconnected.

5. Routewiresfollowingtheappropriatewiringdiagram

forblack,grayorfreshwaterapplications.

6. Includewiresforoptionalelectricalaccessoriesthat

may be part of the installation and shown in separate

wiringdiagrams.

7. Installthecircuitpanelwiththefour#6 fasteners

provided.Makesuretoinstallwiththe“UP”arrow

pointingintheproperdirection.

8. Pushthepanelcoverontothecircuitpaneluntilit

snapsintoplace.

1 2 3 4 5 6 7 8 9

Komentarze do niniejszej Instrukcji

Brak uwag

Sealand DTM04 Tank Monitor System Manual Instrukcja Użytkownika Strona 4

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Sealand DTM04 Tank Monitor System Manual